door bits wanted
3 posters
Page 1 of 1
door bits wanted
hi guys. am in need of the little screws that hold the bearings on the runner. bearings turned up today only took 3 weeks lol
think I only need a couple. would anyone happen to know what there called and where I could get some from.
thanx
rich
think I only need a couple. would anyone happen to know what there called and where I could get some from.
thanx
rich
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
The whole setup looks like this,
The gold bolt and tube hold the bearing on.
http://www.daihatsuhijet.co.uk/repair-hijet-sliding-doors-rough-sticking-grinding-bearings-dropped/
The gold bolt and tube hold the bearing on.
http://www.daihatsuhijet.co.uk/repair-hijet-sliding-doors-rough-sticking-grinding-bearings-dropped/
Re: door bits wanted
ok so I have the bearing thingy with gold screw but am in need of a complete one of those at the bottom right of picture.
least of my troubles though at moment as having water pump issues. have just discovered that I cant take off pump with timing belt still on. and most annoyingly all the hose clips have obviously been put on from underneath the van. pain in the ar*e when you not got a ramp.
am a complete novice by the way if you couldn't tell.
plumber/pipe fitter by trade so not a complete muppet when it comes to technical stuff.
least of my troubles though at moment as having water pump issues. have just discovered that I cant take off pump with timing belt still on. and most annoyingly all the hose clips have obviously been put on from underneath the van. pain in the ar*e when you not got a ramp.
am a complete novice by the way if you couldn't tell.
plumber/pipe fitter by trade so not a complete muppet when it comes to technical stuff.
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
He has the 993 and yes, you do have to take the belt off but only at the top IIRC, so a chalk mark on belt and cog should suffice.
PFM- Jet Addict
- Posts : 1901
Join date : 2010-04-24
Age : 63
Location : East Sussex
Re: door bits wanted
where do I release the tension on the belt guys?
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
so I just pull on number 7 to release the tension. how much play should there be btw?
did try a spanner on it but couldn't get it to move. will try again tomoz.
did try a spanner on it but couldn't get it to move. will try again tomoz.
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
Brill will give it a go tomorrow.I think the hard part is putting it all back together lol just got loads of bits and bucket of nuts and bolts.
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
Hi HJ, did you mention you had one of those vertical runner thingy ma Bob's?
How much are they mate.?
How much are they mate.?
simmo116- Chatterbox
- Posts : 90
Join date : 2012-07-03
Re: door bits wanted
It's more for the labour of actually sorting it out and getting the posted but £3 for a pair of them and £2 for postage.
Just paypal me at threepot@hotmail.co.uk and put your postal address on the paypal info if it isn't already!
Just paypal me at threepot@hotmail.co.uk and put your postal address on the paypal info if it isn't already!
Similar topics
» rear door handel wanted
» [Wanted] A few bits
» WANTED - Petrol fuel tank, Exhaust, DS sliding door handle, OS door handle, Fuel Gauge, Coolant temp sensor
» 13" wheels, Side Window, Towbar and other bits wanted.
» Wanted - Door parts
» [Wanted] A few bits
» WANTED - Petrol fuel tank, Exhaust, DS sliding door handle, OS door handle, Fuel Gauge, Coolant temp sensor
» 13" wheels, Side Window, Towbar and other bits wanted.
» Wanted - Door parts
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|